MasterForce SM3051M Especificaciones descargar pdf (Pagina 15)

Fig.12

9. Removethearborbolt(4),thecollar(6),and

theblade(7).Donotremovetheinnerblade

collar.(Fig.13)

10.Raisethelowerclearplasticbladeguard(1)

totheuprightpositiontoremovetheblade.

(Fig.11)

NOTE:Payattentiontothepiecesremoved,noting

theirpositionanddirectiontheyface.Wipethe

bladecollarscleanofanysawdustbeforeinstalling

anewblade.Also,the12"bladehasa1"arborhole

witha5/8"reducertomountontothesaw.

Fig.13

INSTALLING BLADE (FIG. 11,12, 13)

CAUTION

Un=piug the miter saw before changing/

installing the blade,

1. install a 12 in. blade with a 5/8 in. arbor (or a

1 in. arbor with a 5/8 in. reducer) making sure

the rotation arrow on the blade matches the

clockwise rotation arrow on the upper guard,

and the blade teeth are pointing downward.

2. Place the collar (6) against the blade and on

the arbor. Thread the arbor bolt (4) on the

arbor in a counterclockwise direction. (Fig. 13)

IMPORTANT: Make sure the flats of the blade

collars are engaged with the flats on the arbor

shaft. Also, the flat-side of the collar must be

placed against the blade.

3. Place the blade wrench on the arbor bolt.

4. Press the arbor lock (5), holding it in firmly

while turning the blade counterclockwise. When

it engages, continue to press the arbor lock in,

while tightening the arbor bolt securely. (Fig. 12)

5. Rotate the cover plate (3) back to its original

position until the slot in the cover plate

engages with the cover plate screw (2). While

holding the lower blade guard, tighten the

screw with a Phillips screwdriver. (Fig. 11)

NOTE: The lower blade guard must be raised

to the upright position to access the cover

plate screw.

6. Lower the clear retractable blade guard (1)

and verify the operation of the guard does not

bind or stick (Fig. 11 ).

7. Be sure the arbor lock is released so the

blade turns freely by spinning the blade until

the arbor lock disengages.

CAUTION

® To avoid injury, never use the saw without

the cover plate secure in place, it keeps the

arbor bolt from falling out if it accidentally

loosens, and helps prevent the spinning

blade from coming off the saw,

® Make sure the collars are clean and

properly arranged. Lower the blade into

the table and check for any contact with

the metal base or the turn table,

BEVEL STOP ADJUSTMENTS

(FIG, 14, 15, 16, 17)

CAUTION

To avoid injury from unexpected starting or

electrical shock, make sure the trigger is

released and remove the power cord from the

power source,

90°(0 °) Bevel adjustment (Fig. 14)

1. Loosen bevel lock handle (2) and tilt the

cutting arm while pushing in the bevel detent

pin (1) in against the 0 ° bevel stop. Tighten the

bevel lock handle.

2. Place a combination square on the miter table

with the rule against the table and heel of the

square against the saw blade.

3. If the blade is not 0° to the miter table, loosen

the four adjustment bolts (3) at the rear of

the unit with a 5 mm hex wrench. Unlock the

bevel lock handle (2) and adjust the cutting

arm zero degrees to the table. Tighten the

bevel lock handle and the four adjustment

bolts after alignment is achieved.

Fig. 14

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 37 38

Comentarios a estos manuales

Sin comentarios

MasterForce SM3051M Especificaciones Pagina 15

Comentarios a estos manuales